Skip to main content

Independent. Diagnosis first, parts second.

+1 437-505-5995 nazmul@chromkit.ca

Chromkit
Get a quote
Spectrophotometer and AAS lamps

This is an aftermarket part, not an original manufacturer part. Instrument names and part numbers identify what it fits and replaces; they remain the trademarks of their owners. The manufacturer, country of origin, rated life and warranty are stated in the quote, before you decide anything. If you need the OEM part, say so and I will quote that instead.

Spectrophotometer and AAS lamps

Power supply for Maurice lamp

Replaces OEM part number: L10671P

Power supply for the Maurice lamp, cross-referenced to L10671P. It is the part people order second, after a new lamp fails to fix the fault. A supply that cannot hold the strike voltage gives a lamp that will not light, or one that lights and then goes unstable, and both look like a dead lamp from the front panel. If you have already fitted a new lamp and the symptom has not changed, this is the part. Tell me which way it failed and I will say which one I would order.

Type
Power supply
Fits
ProteinSimple Maurice
Replaces
L10671P
Condition
new
Price
Quoted per order, in Canadian dollars
Request a quote +1 437-505-5995

Before you order: if the instrument is misbehaving, tell me the symptom, not the part number. Lamps and seals get replaced for problems they did not cause. The first look costs nothing, and if this part is not the fix, I will say so.

How buying works, written for procurement →

More for Maurice and similar systems

Illustration of a detector lamp. Generic drawing, not a photograph of this part. Illustration

Spectrophotometer and AAS lamps

Lamp for Maurice

Lamp for the ProteinSimple Maurice, cross-referenced to L10671D. On this instrument the lamp and its power supply are separate parts, and a dim or unstable source can be either one. The power supply is L10671P. Before ordering, note whether the lamp fails to strike at all or strikes and then drifts: a lamp that will not light at all points at the supply more often than at the lamp. Getting that wrong means buying the cheaper part twice.

Type
Detector lamp
Fits
ProteinSimple Maurice
Replaces
L10671D

Price on request

Enquire

Request a quote
Deuterium lamp for Shimadzu detectors and spectrophotometers, flanged base with a flying lead and a keyed connector.

Spectrophotometer and AAS lamps

Deuterium lamp for Shimadzu UV-Vis spectrophotometers

Deuterium lamp for the Shimadzu UV-Vis bench, cross-referenced to 062-65055-05. These are double beam instruments, which hides lamp ageing for longer than a single beam does: the reference beam absorbs some of the drift, so by the time the baseline looks wrong the lamp is usually well past its useful output. The tell is noise creeping up below 250 nm while the visible range still looks clean. Run the instrument's own energy or lamp history check before ordering, and if the noise covers the whole scan the lamp is not your problem.

Type
Deuterium
Fits
Shimadzu UV-3700, 3600, 2700, 2600, 2550, 2450, 1700, 1800, 1240, 1280
Replaces
062-65055-05
RFID chip
No

Price on request

Enquire

Request a quote
Illustration of a detector lamp. Generic drawing, not a photograph of this part. Illustration

Spectrophotometer and AAS lamps

Deuterium lamp for Shimadzu UV-1800 and UV-1900

Deuterium lamp for the UV-1800 and UV-1900, cross-referenced to L6302-40. These benches keep a lamp hour counter, and it is worth reading before you diagnose anything, because a lamp left on continuously accumulates hours far faster than the number of samples suggests. Many labs never switch the source off between runs. If the counter is low and the UV end is still noisy, suspect a dirty cuvette or a fouled window before the lamp. Reset the counter after fitting, or the next person inherits a number that means nothing.

Type
Deuterium
Fits
Shimadzu UV-1800, UV-1900
Replaces
L6302-40

Price on request

Enquire

Request a quote
Deuterium lamp for Thermo and Dionex detectors, flanged base with a six-way keyed connector on a flying lead.

Spectrophotometer and AAS lamps

Lamp for Thermo iCE 3500 AAS

Aftermarket lamp for the Thermo iCE 3500, cross-referenced to 9423-420-30004. A hollow cathode lamp emits the spectral lines of one element, so it is chosen by the element you are measuring and not by the instrument alone. Tell me the element when you enquire. This detector expects a lamp carrying an RFID tag. The chip is listed in the specification above, and it is worth confirming before you order, because a chipless lamp can be refused by the instrument.

Type
AAS lamp
Fits
Thermo iCE 3500
Replaces
9423-420-30004
RFID chip
Yes

CA$1,162

Enquire

Request a quote